欧美久久片软件夜_手机看免费毛片的网站_LSP破解软件库合集链接地址_国产成a人大片在线观看_醉酒后少妇被疯狂内射视频_精品人妻99一区二区三区_日本少妇综合高清_国产醉酒肤白貌美在线观看_最近2024年中文字幕高清_秋霞影院亚洲wm

PXIe-6556
任何PFI引腳都可以從外部輸入WFTRIG信號，該信號可作為PFI6/WFTRIG引腳的輸出。作為輸入，WFTRIG配置為邊緣檢測模式。您可以選擇任何PFI引腳作為WFTRIG的源，并配置上升沿或下降沿的極性選擇。WFTRIG的選定邊緣開始DAC的波形生成。如果選擇內部生成的更新*，則會啟動更新間隔計數器（UI）。作為輸出，WFTRIG反映啟動波形生成的觸發器，即使波形生成是由另一個PFI外部觸發的。輸出為有源高脈沖，脈沖寬度為25至50 ns。該輸出在啟動時設置為高阻抗。圖4-22和4-23顯示了WFTRIG的定時要求。圖4-22：。WFTRIG輸入信號定時圖4-23。WFTRIG輸出信號定時上升沿極性下降沿極性t w t w=10 ns小t w t w=25-50 ns第4章連接信號©National Instruments Corporation 4-29 NI PCI-6110/6111用戶手冊更新*信號任何PFI引腳都可以從外部輸入更新*信號，該信號可作為PFI5/更新*引腳上的輸出。作為輸入，在邊緣檢測模式下配置更新*。您可以選擇任何PFI引腳作為更新*的源，并為上升沿或下降沿配置極性選擇。選定的更新邊*更新DAC的輸出。要使用更新*，必須將DAC設置為發布更新模式。作為輸出，更新*反映連接到DAC的實際更新脈沖，即使更新是由另一個PFI外部生成的。輸出為有效低脈沖，脈沖寬度為50至75 ns。該輸出在啟動時設置為高阻抗。圖4-24和4-25顯示了更新*的時間要求。圖4-24：。更新*輸入信號定時圖4-25。更新*輸出信號定時DAC在前緣100 ns內更新。用足夠的時間分離更新*脈沖，以便新數據可以寫入DAC鎖存器。除非您選擇一些外部源，否則NI PCI-6110/6111UI通常會生成更新*。WFTRIG信號啟動UI，軟件或內部緩沖區計數器可以停止UI。

Any PFI pin can externally input the WFTRIG signal, which is available as an output on the PFI6/WFTRIG pin. As an input, WFTRIG is configured in the edge-detection mode. You can select any PFI pin as the source for WFTRIG and configure the polarity selection for either rising or falling edge. The selected edge of WFTRIG starts the waveform generation for the DACs. The update interval counter (UI) is started if you select internally generated UPDATE*. As an output, WFTRIG reflects the trigger that initiates waveform generation, even if the waveform generation is being externally triggered by another PFI. The output is an active high pulse with a pulse width of 25 to 50 ns. This output is set to high-impedance at startup. Figures 4-22 and 4-23 show the timing requirements for WFTRIG. Figure 4-22. WFTRIG Input Signal Timing Figure 4-23. WFTRIG Output Signal Timing Rising-edge polarity Falling-edge polarity t w t w = 10 ns minimum t w t w = 25-50 ns Chapter 4 Connecting Signals © National Instruments Corporation 4-29 NI PCI-6110/6111 User Manual UPDATE* Signal Any PFI pin can externally input the UPDATE* signal, which is available as an output on the PFI5/UPDATE* pin. As an input, UPDATE* is configured in the edge-detection mode. You can select any PFI pin as the source for UPDATE* and configure the polarity selection for either rising or falling edge. The selected edge of UPDATE* updates the outputs of the DACs. In order to use UPDATE*, you must set the DACs to posted-update mode. As an output, UPDATE* reflects the actual update pulse that is connected to the DACs, even if the updates are being externally generated by another PFI. The output is an active low pulse with a pulse width of 50 to 75 ns. This output is set to high-impedance at startup. Figures 4-24 and 4-25 show the timing requirements for UPDATE*. Figure 4-24. UPDATE* Input Signal Timing Figure 4-25. UPDATE* Output Signal Timing The DACs are updated within 100 ns of the leading edge. Separate the UPDATE* pulses with enough time that new data can be written to the DAC latches. The NI PCI-6110/6111UI normally generates UPDATE* unless you select some external source. The WFTRIG signal starts the UI, and the UI can be stopped by software or the internal Buffer Counter.