產品展示
聯系我們
聯系人：麥女士
手機：+86 15270269218
電話：
Q Q：3136378118
郵箱：stodcdcs@gmail.com
地址：江西省九江市瑞昌市東益路23號賽湖農商城401號
DM476
安裝說明機架安裝1。根據10頁的安裝注意事項，選擇并準備適當的安裝位置。2、使用標準機架安裝硬件將設備安裝在機架中（驅動器入口朝外）。3、將電源線的一端連接到電源插座，另一端連接到正確接地的115/230 VAC、50-60 Hz插座。4、打開電源。系統將啟動到已安裝的操作系統。通過軟盤驅動器或CD-ROM安裝應用軟件。圖2-19。安裝機架安裝硬件帶滑軌的機架安裝1。將設備放置在堅固的工作面上，并斷開所有電纜和跳線與設備的連接。2、將提供的Xycom滑軌（按訂單號1600–RMS單獨訂購）連接到裝置上（見圖2–20）。3、使用標準機架安裝硬件將裝置牢固安裝在機架中，使驅動器檢修門朝外。將導軌安裝螺釘扭轉至35 in/lbs.5。重新連接所有電纜和跳線。15帶奔騰4的1600系列2章-安裝圖2-20。安裝可選的滑軌系統電源在1600的輸入交流電源線上使用隔離變壓器總是一個好主意。在重型設備可能會在交流線路上引入噪聲的情況下，尤其需要使用隔離變壓器。隔離變壓器也可用作降壓變壓器，以將進線電壓降低至所需水平。變壓器應具有足夠的額定功率（單位為伏安），以充分供應負載。正確接地對于所有安全的電氣裝置至關重要。請參閱相關的聯邦、州、省和地方電氣規范，這些規范提供了電氣部件安全接地所需的導線尺寸和類型、顏色代碼和連接等數據。該規范規定，接地路徑必須是性的（無焊料）、連續的，并且能夠在系統中以小阻抗安全地傳導接地故障電流（所需的小導線為18 AWG，1 mm）。遵守以下做法：在外殼入口點將地線（P.E.或保護接地）與電源線分開。為盡量減少外殼內的地線長度，將接地參考點定位在工廠電源入口附近。所有電氣機架或底盤和機器元件應在預計會產生高電氣噪聲的安裝中接地。用接地棒將機箱接地，或連接到附近的接地結構上，如鋼支撐梁。每個不同的設備應連接到具有低阻抗電纜的“星形”配置中的單個接地點。從機箱與外殼接觸的區域刮去油漆和其他不導電材料。除了通過安裝螺栓或螺柱進行接地連接外，還應使用一英寸的金屬編織物或尺寸為#8 AWG的電線連接每個機箱和安裝螺栓或螺柱處的外殼。
Mounting Instructions Rack Mounting 1. Select and prepare an appropriate mounting location according to the Mounting Considerations on page 10. 2. Install the unit in the rack (with drive access facing outward) using the standard rack-mounting hardware. 3. Attach one end of the power cord to the power receptacle and the other end to a properly grounded 115/230 VAC, 50-60 Hz outlet. 4. Turn on the power. The system will boot up to the installed operating system. 5. Install application software via a floppy drive or CD-ROM. Figure 2–19. Installing Rack Mounting Hardware Rack Mounting with Slide Rails 1. Place the unit on a solid work surface and disconnect all cables and cords from the unit. 2. Attach the provided Xycom slide rails (ordered separately by order number 1600–RMS) to the unit (see Figure 2–20). 3. Install the unit securely in the rack with standard rack-mounting hardware so that the drive access door faces outward. 4. Torque the rail-mounting screws to 35 in/lbs. 5. Reconnect all cables and cords. 15 1600 Series with Pentium 4 Chapter 2 – Installation Figure 2–20. Installing Optional Slide Rails System Power It is always a good idea to use isolation transformers on the incoming AC power line to the 1600. An isolation transformer is especially desirable in cases where heavy equipment is likely to introduce noise onto the AC line. The isolation transformer can also serve as a step-down transformer to reduce the incoming line voltage to a desired level. The transformer should have a sufficient power rating (units of volt-amperes) to supply the load adequately. Proper grounding is essential to all safe electrical installations. Refer to the relevant Federal, State, Provincial, and local electric codes that provide data such as the size and types of conductors, color codes and connections necessary for safe grounding of electrical components. The code specifies that a grounding path must be permanent (no solder), continuous, and able to safely conduct the ground-fault current in the system with minimal impedance (minimum wire required is 18 AWG, 1 mm). Observe the following practices: Separate ground wires (P.E. or Protective Earth) from power wires at the point of entry to the enclosure. To minimize the ground wire length within the enclosure, locate the ground reference point near the point of entry for the plant power supply. All electrical racks or chassis and machine elements should be Earth Grounded in installations where high levels of electrical noise are expected. Ground the chassis with a ground rod or attach to a nearby Earth structure such as a steel support beam. Each different apparatus should be connected to a single Earth Ground point in a “star” configuration with low impedance cable. Scrape away paint and other nonconductive material from the area where a chassis makes contact with the enclosure. In addition to the ground connection made through the mounting bolt or stud, use a one-inch metal braid or size #8 AWG wire to connect between each chassis and the enclosure at the mounting bolt or stud.
相關產品
