欧美久久片软件夜_手机看免费毛片的网站_LSP破解软件库合集链接地址_国产成a人大片在线观看_醉酒后少妇被疯狂内射视频_精品人妻99一区二区三区_日本少妇综合高清_国产醉酒肤白貌美在线观看_最近2024年中文字幕高清_秋霞影院亚洲wm

AS-BADU-254C
參數值說明對比度1-9增大或減小該值以增大或減小顯示對比度。Bcklght Timeout（min）0-60設置一段時間不活動后背光關閉前的時間（分鐘）。將其設置為“0”將禁用背光超時功能（即背光始終打開）。屏幕超時（分鐘）0-60設置一段時間不活動后屏幕關閉前的時間（分鐘）。將其設置為“0”將禁用屏幕超時功能（即顯示器始終打開）。QR Code Enable（啟用）、Disable（禁用）設置顯示屏上是否有嵌入數據的QR Code（）。您可以使用顯示器配置基本儀表參數。儀表基本設置參數的正確配置對于準確測量和計算至關重要。使用基本設置屏幕定義電表正在監測的電力系統。如果已配置標準（1秒）報警，并且您對儀表的基本設置進行了后續更改，則會禁用所有報警，以防止意外的報警操作。警告意外設備操作•驗證所有標準警報設置是否正確，并根據需要進行調整。•重新啟用所有配置的報警。不遵守這些說明可能導致死亡、重傷或設備損壞。保存更改后，確認所有配置的標準報警設置仍然有效，根據需要重新配置，然后重新啟用報警。1、導航至Maint>Setup。2、輸入設置密碼（默認為“0”），然后按OK。3、導航至儀表>基本。4、移動光標指向要修改的參數，然后按編輯。5、根據需要修改參數，然后按OK。6、移動光標指向要修改的下一個參數，按Edit，進行更改，然后按OK。

Parameter Values Description Contrast 1 - 9 Increase or decrease the value to increase or decrease the display contrast. Bcklght Timeout (min) 0 - 60 Set how long (in minutes) before the backlight turns off after a period of inactivity. Setting this to “0” disables the backlight timeout feature (i.e., backlight is always on). Screen Timeout (min) 0 - 60 Set how long (in minutes) before the screen turns off after a period of inactivity. Setting this to “0” disables the screen timeout feature (i.e., display is always on). QR Code Enable, Disable Set whether or not QR codes with embedded data are available on the display.You can configure basic meter parameters using the display. Proper configuration of the meter’s basic setup parameters is essential for accurate measurement and calculations. Use the Basic Setup screen to define the electrical power system that the meter is monitoring. If standard (1-sec) alarms have been configured and you make subsequent changes to the meter’s basic setup, all alarms are disabled to prevent undesired alarm operation. WARNING UNINTENDED EQUIPMENT OPERATION • Verify all standard alarms settings are correct and make adjustments as necessary. • Re-enable all configured alarms. Failure to follow these instructions can result in death, serious injury, or equipment damage. After saving the changes, confirm all configured standard alarm settings are still valid, reconfigure them as required, and re-enable the alarms. 1. Navigate to Maint > Setup. 2. Enter the setup password (default is “0”), then press OK. 3. Navigate to Meter > Basic. 4. Move the cursor to point to the parameter you want to modify, then press Edit. 5. Modify the parameter as required, then press OK. 6. Move the cursor to point to the next parameter you want to modify, press Edit, make your changes, then press OK.