產品展示
聯系我們
聯系人：麥女士
手機：+86 15270269218
電話：
Q Q：3136378118
郵箱：stodcdcs@gmail.com
地址：江西省九江市瑞昌市東益路23號賽湖農商城401號
DS3820PIMB
每相并聯電纜的校正系數：大值
表2（TN系統）或表3（IT系統）中讀取的保護長度應為
乘以以下系數：
n 2 3 4 5 6 7 8
kp 2 2.7 3 3.2 3.3 3 3.4 3.5
n是每相并聯的導體數量
三相電壓不同于400 V的校正系數：的值
表2（TN系統）或表3（IT系統）中讀取的大保護長度
應乘以以下系數：
電壓【V】230 400 440 500 690
kV 0.58 1 1.1 1.25 1.73
對于230 V單相系統，無需校正系數。
鋁制電纜的修正系數：大保護值
表2（TN系統）或表3（IT系統）中讀取的長度應乘以
以下因素：
kAl 0.64
保護導體橫截面修正系數SPE不同
根據表1中規定的橫截面：大保護長度的值應乘以對應于相位的系數
導體橫截面和保護導體之間的比率（PE）
以及相位橫截面：
SPE/S 0.5 0.55 0.6 0.66 0.75 0.87 1 1 1.25 1.5 2
S kPE
≤16 mm2 0.67 0.71 0.75 0.80 0.86 0.93 1.00 1.11 1.20 1.33
25 mm2 0.85 0.91 0.96 1.02 1.10 1.19 1.28 1.42 1.54 1.71
35 mm2 1.06 1.13 1.20 1.27 1.37 1.48 1.59 1.77 1.91 2.13
>35 mm2 1.00 1.06 1.13 1.2 1.29 1.39 1.5 1.67 1.8 2.00
IT系統中分布的中性點校正系數（僅適用于表3）：
大保護長度值應乘以0.58。
464電氣設備| ABB
5座光伏電站
光伏（PV）發電廠直接瞬時轉換太陽能
在不使用任何燃料的情況下轉化為電能。事實上，光伏（PV）技術利用了光電效應，通過光電效應
適當“摻雜”的半導體在暴露于太陽能時發電
輻射
光伏（PV）電站的主要優勢可總結如下：
•必要時進行分布式發電；
•無污染材料排放；
•節約化石燃料；
•設備的可靠性，因為它們沒有活動部件（使用壽命
通常超過20年）；
•降低運營和維護成本；
•系統模塊化（為了增加電廠功率，足以提高
面板數量）根據用戶的實際要求。
然而，由于
從技術和經濟角度來看尚未完全成熟的市場
觀點。此外，由于可變性，發電不穩定
太陽能的能量。
光伏電站的年電力輸出取決于不同的因素。
其中：
•安裝現場的太陽輻射事件；
•面板的傾斜和方向；
•是否有陰影；
•電廠組件的技術性能（主要是模塊和
逆變器）。
光伏電站的主要應用包括：
1.為與電網隔離的用戶安裝（帶存儲系統）；
2、接入低壓電網的用戶裝置；
3.太陽能光伏發電廠，通常連接到中壓電網。
上網電價優惠僅適用于2類和3類應用，
額定功率不低于1 kW的電廠。
光伏發電廠基本上由發電機（光伏板）和
將面板安裝在地面、建筑物或任何建筑物上的框架
結構，通過功率控制和調節系統，通過可能的能量
存儲系統，通過配電盤和開關設備組件外殼
開關和保護設備以及連接電纜。
Correction factor for cable in parallel per phase: the value of the maximum protected length read in Table 2 (TN system) or Table 3 (IT system) shall be multiplied by the following factor: n 2 3 4 5 6 7 8 kp 2 2.7 3 3.2 3.3 3.4 3.5 n is the number of conductors in parallel per phase Correction factor for three-phase voltage different from 400 V: the value of the maximum protected length read in Table 2 (TN system) or Table 3 (IT system) shall be multiplied by the following factor: voltage [V] 230 400 440 500 690 kV 0.58 1 1.1 1.25 1.73 For 230 V single-phase systems, no correction factor is necessary. Correction factor for aluminium cables: the value of the maximum protected length read in Table 2 (TN system) or Table 3 (IT system) shall be multiplied by the following factor: kAl 0.64 Correction factor for protective conductor cross section SPE different from the cross sections stated in Table 1: the value of the maximum protected length shall be multiplied by the coefficient corresponding to the phase conductor cross section and to the ratio between the protective conductor (PE) and the phase cross sections: SPE/S 0.5 0.55 0.6 0.66 0.75 0.87 1 1.25 1.5 2 S kPE ≤16 mm2 0.67 0.71 0.75 0.80 0.86 0.93 1.00 1.11 1.20 1.33 25 mm2 0.85 0.91 0.96 1.02 1.10 1.19 1.28 1.42 1.54 1.71 35 mm2 1.06 1.13 1.20 1.27 1.37 1.48 1.59 1.77 1.91 2.13 >35 mm2 1.00 1.06 1.13 1.2 1.29 1.39 1.5 1.67 1.8 2.00 Correction factor for neutral distributed in IT systems (for Table 3 only): the value of the maximum protected length shall be multiplied by 0.58. 464 Electrical devices | ABB 5 Photovoltaic plants A photovoltaic (PV) plant transforms directly and instantaneously solar energy into electrical energy without using any fuels. As a matter of fact, the photovoltaic (PV) technology exploits the photoelectric effect, through which some semiconductors suitably “doped” generate electricity when exposed to solar radiation. The main advantages of photovoltaic (PV) plants can be summarized as follows: • distribuited generation where needed; • no emission of polluting materials; • saving of fossil fuels; • reliability of the plants since they do not have moving parts (useful life usually over 20 years); • reduced operating and maintenance costs; • system modularity (to increase the plant power it is sufficient to raise the number of panels) according to the real requirements of users. However, the initial cost for the development of a PV plant is quite high due to a market which has not reached its full maturity from a technical and economical point of view. Moreover the generation of power is erratic due to the variability of the solar energy source. The annual electrical power output of a PV plant depends on different factors. Among them: • solar radiation incident on the installation site; • inclination and orientation of the panels; • presence or not of shading; • technical performances of the plant components (mainly modules and inverters). The main applications of PV plants are: 1.installations (with storage systems) for users isolated from the grid; 2. installations for users connected to the LV grid; 3.solar PV power plants, usually connected to the MV grid. Feed-in Tariff incentives are granted only for the applications of type 2 and 3, in plants with rated power not lower than 1 kW. A PV plant is essentially constituted by a generator (PV panels), by a supporting frame to mount the panels on the ground, on a building or on any building structure, by a system for power control and conditioning, by a possible energy storage system, by electrical switchboards and switchgear assemblies housing the switching and protection equipment and by the connection cables.
相關產品
