產品展示
聯系我們
聯系人：麥女士
手機：+86 15270269218
電話：
Q Q：3136378118
郵箱：stodcdcs@gmail.com
地址：江西省九江市瑞昌市東益路23號賽湖農商城401號
9907-105
加載控制用于軟化
負載共享的加載和加載
循環：加載由
輔助發電機斷路器
聯系卸載由
卸載瞬時打開
聯系當斷路器
關閉時，負載將增加
以預設爬坡率，直到
與其他單位匹配。這個
AGLC然后跟蹤
在卸載信號上設置和
使集合以斜坡速度卸載。當達到卸載跳閘水平時
繼電器在AGLC中激活，可用于打開斷路器以實現平穩，
無顛簸功率傳輸。
AGLC用于將1至15臺發電機組的基本負荷加入公用事業：基本負荷
參考開關閉合或跨接，控制裝置自動導致系統
斷路器閉合后，斜坡至預設的基本負載水平。
使用內部電位計或外部電位計設置基本負載。這個
基本負載設置可用于增加或減少機組或系統上的負載。
限制可防止基本負載設置為高于大期望負載。
AGLC用于在離開母線之前卸載發電機組：卸載跳閘水平
通過AGLC上的電位計或外部電位計進行調整。當
卸載開關瞬時打開，AGLC使機組或系統下降
至之前設置的觸發點，停止卸載并激活繼電器，該繼電器可以
用于打開斷路器。斷路器斷開時，繼電器復位。
在關閉之前，跳閘水平可與機器上的鼓風機或泵負載相匹配
公共汽車這種使用消除了在與其他部件分離時負載和碰撞的轉移
系統
描述
AGLC自動發電機負載控制用于伍德沃德負載共享
以及帶有內置或外部負載傳感器的速度控制系統。其設計目的是
將發電機組軟加載或軟卸載至負載共享系統或從負載共享系統卸載至
控制費率。它還可以軟加載或卸載單個單元，或多15個并聯負載
共享單元，與公用設施并聯或并聯，然后在
發電系統。
多功能控制簡化了執行這些功能所需的邏輯和接線。
電子斜坡可在5秒到5分鐘之間輕松調整，達到100%
負載變化。（實際加載和卸載時間將取決于發動機的性能。）
加載和卸載爬坡率分別調整。
AGLC始終跟蹤發電機組上的負載，并在
在機組上加載，消除任何顛簸，并提供平穩的功率傳輸，無論
裝載或卸載。
Loading Control is used to soft load in and out of a load sharing loop: Loading is initiated by a generator circuit breaker auxiliary contact. Unloading is initiated by a momentary opening of an unload contact. When the circuit breaker closes, the load will be increased at the preset ramp rate until matched with other units. The AGLC then tracks the load on the set and, on the unload signal causes the set to unload at the ramp speed. When the unload trip level is reached, a relay activates in the AGLC which can be used to open the breaker for a smooth, bumpless power transfer. The AGLC is used to base load 1 to 15 generator sets joining a utility: The base-load reference switch is closed or jumpered, and the control automatically causes the system to ramp to the preset base-load level after the breaker closes. The base load is set with an internal potentiometer, or an external potentiometer. The base load setting can be used to increase or decrease load on the set or on the system. A limit prevents the base load from being set higher than the maximum desired load. The AGLC is used to unload a generator set before leaving the bus: The unload trip level is adjusted by a potentiometer on the AGLC, or by an external potentiometer. When the unload switch is momentarily opened, the AGLC causes the set or system to ramp down to the previously set trip point where it stops unloading and activates a relay which can be used to open the breaker. The relay resets when the breaker opens. The trip level can be matched to blower or pump loads on the machine before closing the bus. This use eliminates a shift of load and bump when separating from the rest of the system. Description The AGLC Automatic Generator Loading Control is for use with Woodward load sharing and speed control systems with either built-in or external load sensors. It is designed to provide soft loading or unloading of a generator set into or out of a load sharing system at controlled rates. It can also soft load or unload a single unit, or up to 15 paralleled load sharing units, into or out of parallel with a utility, and then set a specific base load on the generating system. The versatile control simplifies the logic and wiring required to perform these functions. The electronic ramps are easily adjusted from 5 seconds to 5 minutes for 100 percent load change. (Actual load and unload times will depend on the capabilities of the engine.) The load and unload ramp rates are separately adjusted. The AGLC tracks the load on the generator set at all times and starts the ramp at the load on the set, eliminating any bump and providing smooth transfer of power, whether loading or unloading.
相關產品
