欧美久久片软件夜_手机看免费毛片的网站_LSP破解软件库合集链接地址_国产成a人大片在线观看_醉酒后少妇被疯狂内射视频_精品人妻99一区二区三区_日本少妇综合高清_国产醉酒肤白貌美在线观看_最近2024年中文字幕高清_秋霞影院亚洲wm

8901-881
原動機將
不接受全部
負載
調速器是否已滿
燃料
是的-
1、懸掛機構是否調整正確？
2、負載是否過大？
電壓調節器（如使用）是否設置正確？
4、原動機上的燃油擋塊設置是否正確？
否-
1、負載極限是否超出范圍，是否調整正確？
2、燃油限制（如有配備）是否設置得過低？
3、燃油限制器是否有足夠的氣壓？
4、懸掛機構是否粘滯或調整不當？
如果電動起動燃油限制器有足夠的電壓
電磁閥？
針閥
調整確實
未消除
不穩定。
（1） 是振蕩
周期性且平滑
（非間歇）？
是的-
轉至問題（2）。
否-
檢查以下各項：
1、燃料來源是否充足且穩定？
2、速度設定參考是否穩定？
3、調速器油位是否低？
4、負載是否不穩定？
調速器油是否干凈？
（2） 是的頻率
高于5的振蕩
赫茲？
是的-
檢查以下各項：
調速器傳動系。
調速器對準。
彈簧驅動油阻尼球頭臟污（如有配備）。
4、噴油器損壞或缺火？
否-
轉至問題（3）。
（3） 是振蕩
與速度設置相關
變化？
是的-
必須找到速度設置變化的原因，并
已更正。
否-
轉至問題（4）。
（4） 振蕩
消失時
阻塞調速器
輸出或運行
手動油門？
是的-
1、連桿是否松動或磨損？
調速器零件號是否適用于此應用？
3、更換調速器。
否-
1、檢查負載波動。
2、檢查燃油供應。
3、檢查連桿是否松動或粘滯。
阻塞調速器輸出或操作手時
油門，系統不受調速器控制，以及
必須格外小心，防止超速。做
如果超速速度裝置不工作，請勿嘗試。
調速器不會
關閉原動機
向下
調速器是否小
燃油位置？
是的-
懸掛機構設置不當，導致停機。
否-
調速器上是否有停機驅動信號？
2、停機是否適當調整？
調速器中的停機帶是否已正確調整？
4、關閉燃油，更換調速器。

Prime mover will not accept full load. Is the governor at full fuel? YES— 1. Is the linkage adjusted properly? 2. Is load excessive? 3. Is the voltage regulator (if used) set properly? 4. Is the fuel stop on the prime mover set correctly? NO— 1. Is the load limit out of the way, and adjusted properly? 2. Is the fuel limited (if so equipped) set too low? 3. Is there adequate air pressure for the fuel limiter? 4. Is the linkage sticky or improperly adjusted? 5. If electric start fuel limiter—is there adequate voltage for the solenoid? Needle valve adjustment does not eliminate instability. (1) Are the oscillations periodic and smooth (not intermittent)? YES— Go to question (2). NO— Check the following: 1. Is the fuel source adequate and constant? 2. Is the speed setting reference steady? 3. Is the governor oil level low? 4. Is the load erratic? 5. Is the governor oil clean? (2) Is the frequency of the oscillation above 5 Hz? YES— Check the following: 1. Governor drive train. 2. Governor alignment. 3. Dirty spring-driven oil damped ballhead (if so equipped). 4. Bad injector or misfire? NO— Go to question (3). (3) Are the oscillations related to speed setting variations? YES— The cause of the speed setting variation must be found and corrected. NO— Go to question (4). (4) Does the oscillation disappear when blocking governor output or operating hand throttle? YES— 1. Is linkage loose or worn? 2. Is governor part number correct for this application? 3. Replace governor. NO— 1. Check for load fluctuations. 2. Check fuel supply. 3. Check for loose or sticky linkage. When blocking governor output or operating the hand throttle, the system is not under governor control, and extreme caution must be taken to prevent overspeed. Do not attempt if overspeed speed device is not functioning. Governor will not shut prime mover down. Is governor at minimum fuel position? YES— Linkage is improperly set to allow shutdown. NO— 1. Is shutdown actuation signal available at the governor? 2. Are shutdowns properly adjusted? 3. Is shutdown strap in governor properly adjusted? 4. Close off fuel and replace governor.