產品展示
聯系我們
聯系人：麥女士
手機：+86 15270269218
電話：
Q Q：3136378118
郵箱：stodcdcs@gmail.com
地址：江西省九江市瑞昌市東益路23號賽湖農商城401號
XVME113
安裝注意事項
本節介紹在將1600放入
圈占地
考慮以下要點和注意事項：
選擇一個機柜并將設備放置在便于訪問的位置
1600個端口。
選擇外殼深度時，考慮裝置的深度。
裝置必須安裝在經批準的防火和電氣外殼中。
本節中的安裝尺寸和說明見11頁至15頁
章
考慮AC電源插座等附件的安裝位置，以及
維護方便。
通過安裝恒溫器控制的加熱器或空氣防止冷凝
護發素。
為實現大冷卻，避免阻礙氣流。
將所有風扇或鼓風機靠近發熱設備。如果使用風扇，
確保外部空氣不會進入外殼內部，除非使用織物或其他
使用可靠的過濾器。這種過濾可防止導電顆?；蚱渌?br />有害污染物進入外殼。
不要選擇產生過多電磁波的設備附近的位置
干擾（EMI）或射頻接口（RFI）（高
電力焊機、感應加熱設備和大型電機起動器）。
放置進線電源線設備（如隔離或恒壓
變壓器、本地電源斷路器和浪涌抑制器）遠離
進線設備的正確位置使電源線按照
盡可能短，并將傳輸?shù)?600的電氣噪音降至低。
電源線插座必須安裝在設備附近，并且應易于
可到達的
避免電源電路過載。
在固定接線中加入易于接近的斷開裝置
連接的系統。
確保位置不超過1600的沖擊、振動和
溫度規格。
Mounting Considerations This section describes issues you must address before placing the 1600 inside an enclosure. Consider the following points and precautions: Select an enclosure and place the unit in a position that allows easy access to the 1600 ports. Account for the unit’s depth when choosing the depth of the enclosure. The unit must be mounted in an approved fire and electrical enclosure. See pages 11 through 15 for mounting dimensions and instructions in this chapter. Consider locations of accessories such as AC power outlets for installation and maintenance convenience. Prevent condensation by installing a thermostat-controlled heater or air conditioner. To allow for maximum cooling, avoid obstructing the airflow. Place any fans or blowers close to the heat generating devices. If using a fan, ensure that outside air is not brought inside the enclosure unless a fabric or other reliable filter is used. This filtration prevents conductive particles or other harmful contaminants from entering the enclosure. Do not select a location near equipment that generates excessive electromagnetic interference (EMI) or radio frequency interface (RFI) (equipment such as high power welding machines, induction heating equipment and large motor starters). Place incoming power line devices (such as isolation or constant voltage transformers, local power disconnects, and surge suppressers) away from the 1600. The proper location of incoming line devices keeps power wire runs as short as possible and minimizes electrical noise transmitted to the 1600. The power cord outlet must be installed near the equipment and shall be easily accessible. Avoid overloading the supply circuit. Incorporate a readily accessible disconnect device in the fixed wiring for permanently connected systems. Make sure the location does not exceed the 1600’s shock, vibration, and temperature specifications.
相關產品
