欧美久久片软件夜_手机看免费毛片的网站_LSP破解软件库合集链接地址_国产成a人大片在线观看_醉酒后少妇被疯狂内射视频_精品人妻99一区二区三区_日本少妇综合高清_国产醉酒肤白貌美在线观看_最近2024年中文字幕高清_秋霞影院亚洲wm

MVI71-101M
ModDef設置
MCM。配置。MODDEF標記定義用于讀取的5000個數據寄存器
并在MVI56-MCM模塊內寫入數據。您將使用這些數據讀取和
在每個主命令內的IntAddress標記中寫入位置（第45頁）。
下圖顯示了示例程序中的值。
WRITESTARTREG標記確定
WRITEDATA[0到599]數組。WRITEREGCNT標記確定
5000個寄存器用于向模塊發送數據。示例梯形圖文件使用
600個寫數據寄存器，標記為MCM。WRITEDATA[0到599]。
標簽說明
WRITESTARTREG指定在5000寄存器模塊內存中放置發送數據的位置
來自ControlLogix處理器中的WriteData標記。
WRITEREGCNT指定MVI56-MCM模塊將有多少個數據寄存器
來自ControlLogix處理器的請求。因?yàn)槟K頁面
數據以200字為單位，此數字必須能被
200
READSTARTREG指定模塊讀取數據區域中要發送到的寄存器
ControlLogix處理器中的ReadData標記。
READREGCNT設置MVI56-MCM模塊將發送到的數據寄存器數量
ControlLogix處理器。該值還應為200的倍數。
BPFAIL設置將導致
模塊停止Modbus網絡上的通信。通常使用
當模塊配置為從模塊時。
ERRSTATPTR也主要用于將模塊配置為從屬模塊時。這
參數將狀態數據放置到模塊的數據庫中。

ModDef Settings The MCM.CONFIG.MODDEF tag defines the 5000 data registers to use for read and write data within the MVI56-MCM module. You will use these data read and write locations in the IntAddress tag within each Master Command (page 45). The following illustration shows the values from the sample program. The WRITESTARTREG tag determines the starting register location for the WRITEDATA[0 to 599] array. The WRITEREGCNT tag determines how many of the 5000 registers to use to send data to the module. The sample ladder file uses 600 registers for write data, labeled MCM.WRITEDATA[0 to 599]. Label Description WRITESTARTREG Specifies where in the 5000 register module memory to place data sent from the WriteData tags in the ControlLogix processor. WRITEREGCNT Specifies how many registers of data the MVI56-MCM module will request from the ControlLogix processor. Because the module pages data in blocks of 200 words, this number must be evenly divisible by 200. READSTARTREG Specifies which registers in the module’s read data area to send to the ReadData tags in the ControlLogix processor. READREGCNT Sets how many registers of data the MVI56-MCM module will send to the ControlLogix processor. This value should also be a multiple of 200. BPFAIL Sets the consecutive number of backplane failures that will cause the module to stop communications on the Modbus network. Typically used when the module is configured as a Slave. ERRSTATPTR Also used mainly when the module is configured as a Slave. This parameter places the STATUS data into the database of the module.