產品展示
聯系我們
聯系人：麥女士
手機：+86 15270269218
電話：
Q Q：3136378118
郵箱：stodcdcs@gmail.com
地址：江西省九江市瑞昌市東益路23號賽湖農商城401號
MVI69-DFNT
在機架中安裝模塊
如果尚未安裝和配置ControlLogix處理器
電源，請?jiān)诎惭bMVI模塊之前進行此操作。提到
有關安裝說明的羅克韋爾自動化產品文檔。
警告：安裝此電子設備或任何其他電子設備時，必須遵守所有安全說明
設備。不遵守安全程序可能會導致硬件或數據損壞，甚至
人員重傷或死亡。請參閱計劃安裝的每個設備的文檔
在安裝或維修之前，連接以驗證是否有適當?shù)陌踩绦?br />裝置
檢查跳線位置后，將MVI插入
ControlLogix機箱。使用羅克韋爾推薦的相同技術
自動移除和安裝ControlLogix模塊。
警告：當您在背板電源打開的情況下插入或卸下模塊時，會發生電弧
可能發生。這可能會導致危險位置裝置發生爆炸。驗證電源是否正常
繼續之前，應移除或該區域無危險。重復的電弧原因
模塊及其配套接頭上的觸點過度磨損。磨損的觸點可能
產生可能影響模塊操作的電阻。
1關閉電源。
2將模塊與頂部和底部導軌對齊，然后將其滑入機架
直到模塊牢固抵住背板連接器。
3用力平穩推動，將模塊卡入到位。
4檢查模塊頂部和底部的固定夾是否牢固
在機架的鎖孔中。
5記下插槽位置。您必須標識
安裝模塊是為了使示例程序正常工作。狹槽
數字標識在的綠色電路板（背板）上
ControlLogix機架。
6打開電源。
注意：如果插入模塊不當，系統可能會停止工作，或者可能會出現以下情況
不可預見地
Installing the Module in the Rack If you have not already installed and configured your ControlLogix processor and power supply, please do so before installing the MVI module. Refer to your Rockwell Automation product documentation for installation instructions. Warning: You must follow all safety instructions when installing this or any other electronic devices. Failure to follow safety procedures could result in damage to hardware or data, or even serious injury or death to personnel. Refer to the documentation for each device you plan to connect to verify that suitable safety procedures are in place before installing or servicing the device. After you have checked the placement of the jumpers, insert MVI into the ControlLogix chassis. Use the same technique recommended by Rockwell Automation to remove and install ControlLogix modules. Warning: When you insert or remove the module while backplane power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations. Verify that power is removed or the area is non-hazardous before proceeding. Repeated electrical arcing causes excessive wear to contacts on both the module and its mating connector. Worn contacts may create electrical resistance that can affect module operation. 1 Turn power OFF. 2 Align the module with the top and bottom guides, and slide it into the rack until the module is firmly against the backplane connector. 3 With a firm but steady push, snap the module into place. 4 Check that the holding clips on the top and bottom of the module are securely in the locking holes of the rack. 5 Make a note of the slot location. You must identify the slot in which the module is installed in order for the sample program to work correctly. Slot numbers are identified on the green circuit board (backplane) of the ControlLogix rack. 6 Turn power ON. Note: If you insert the module improperly, the system may stop working, or may behave unpredictably
相關產品
