產品展示
聯系我們
聯系人：麥女士
手機：+86 15270269218
電話：
Q Q：3136378118
郵箱：stodcdcs@gmail.com
地址：江西省九江市瑞昌市東益路23號賽湖農商城401號
MVME333X25
模塊安裝在安裝了EPROM和IndustryPack并正確配置了標頭的情況下，按照以下步驟在VME機箱中安裝MVME：1。關閉所有設備電源，并斷開電源線與交流電源的連接。注意：通電時插入或拆卸模塊可能會損壞模塊組件！警告：此設備中存在可能導致死亡的危險電壓。在搬運、測試和調整時要格外小心。2、按照設備用戶手冊中的說明卸下機箱蓋。3、從要安裝MVME的卡槽中卸下填充板如果要將MVME用作系統控制器，它必須占用左側的卡插槽（插槽1）。系統控制器必須位于插槽1中，以正確啟動總線授權菊花鏈，并確保IACK菊花鏈驅動程序的正確操作如果不打算將MVME用作系統控制器，它可能會占用任何未使用的雙高卡插槽。4、將MVME滑入所選卡槽。確保模塊正確安裝在背板上的P1和P2接頭中。不要損壞或彎曲接頭針腳。5、使用提供的螺釘將MVME固定在機箱中，與橫向安裝導軌保持良好接觸，以盡量減少射頻發射。將MVME712系列轉換模塊安裝在VME機箱的前部或后部。（要安裝具有雙寬前面板的MVME712M，您可能需要移動機箱中的其他模塊。）7、在機箱背板上，從MVME占用的卡插槽的標頭上卸下中斷確認（IACK）和總線授權（BG）跳線。
Module Installation With EPROM and IndustryPacks installed and headers properly configured, proceed as follows to install the MVME in the VME chassis: 1. Turn all equipment power OFF and disconnect the power cable from the AC power source. Caution Inserting or removing modules while power is applied could result in damage to module components. ! WARNING Dangerous voltages, capable of causing death, are present in this equipment. Use extreme caution when handling, testing, and adjusting. 2. Remove the chassis cover as instructed in the user’s manual for the equipment. 3. Remove the filler panel from the card slot where you are going to install the MVME. – If you intend to use the MVME as system controller, it must occupy the leftmost card slot (slot 1). The system controller must be in slot 1 to correctly initiate the bus-grant daisy-chain and to ensure proper operation of the IACK daisy-chain driver. – If you do not intend to use the MVME as system controller, it can occupy any unused double-height card slot. 4. Slide the MVME into the selected card slot. Be sure the module is seated properly in the P1 and P2 connectors on the backplane. Do not damage or bend connector pins. 5. Secure the MVME in the chassis with the screws provided, making good contact with the transverse mounting rails to minimize RF emissions. 6. Install the MVME712 series transition module in the front or the rear of the VME chassis. (To install an MVME712M, which has a double-wide front panel, you may need to shift other modules in the chassis.) 7. On the chassis backplane, remove the INTERRUPT ACKNOWLEDGE (IACK) and BUS GRANT (BG) jumpers from the header for the card slot occupied by the MVME.
相關產品
