產品展示
聯系我們
聯系人：麥女士
手機：+86 15270269218
電話：
Q Q：3136378118
郵箱：stodcdcs@gmail.com
地址：江西省九江市瑞昌市東益路23號賽湖農商城401號
MVME177PA-64SE
安裝新SIM卡
1、觀察SIM卡接頭J1和
接頭J10。轉動SIM卡，使鑰匙對齊并放置
將其輕輕地安裝在連接器J10上，對準SIM卡拐角處的安裝孔
與上的對峙相匹配。
2、輕按SIM卡頂部，將其固定在連接器上。如果SIM卡有
不要用溫和的壓力坐好，重新檢查方向。如果SIM卡連接器
如果方向不正確，安裝孔將與
僵局。
警告：如果SIM卡方向不正確，請不要試圖強行打開SIM卡。
3、放置兩個4-40 x 3
/之前使用的16“十字頭螺釘
已將（或新SIM卡附帶的）插入兩個相對的角安裝孔中。將其擰入防區，但不要
過緊。
各種串行通信中的信號關系和信號連接
端口A和B的可用配置如圖2-3、2-4所示，
和2-5。
系統控制器選擇收割臺（J1）
出廠時配置為VMEbus系統控制器（即
跨接導線安裝在收割臺J1的針腳1和2之間。如果出現以下情況，請拆下J1跨接導線
不是系統控制器。請注意，當
用作系統控制器，SCON LED亮起。
注：對于無可選VMEbus接口的s（即。，
無VMEchip2），可安裝或拆除跳線
不影響正常運行。
J1
2.
1.
2.
1.
J1
系統控制器（出廠配置）非系統控制器
Installation of New SIM 1. Observe the orientation of the connector keys on SIM connector J1 and connector J10. Turn the SIM so that the keys line up and place it gently on connector J10, aligning the mounting holes at the SIM corners with the matching standoffs on the . 2. Gently press the top of the SIM to seat it on the connector. If the SIM does not seat with gentle pressure, recheck the orientation. If the SIM connector is oriented incorrectly, the mounting holes will not line up with the standoffs. Caution Do not attempt to force the SIM on if it is oriented incorrectly. 3. Place the two 4-40 x 3 /16” Phillips-head screws that you previously removed (or that were supplied with the new SIM) into the two oppositecorner mounting holes. Screw them into the standoffs but do not overtighten them. The signal relationships and signal connections in the various serial configurations available for ports A and B are illustrated in Figures 2-3, 2-4, and 2-5. System Controller Select Header (J1) The is factory-configured as a VMEbus system controller (i.e., a jumper is installed across pins 1 and 2 of header J1). Remove the J1 jumper if the is not to be the system controller. Note that when the is functioning as system controller, the SCON LED is turned on. Note For s without the optional VMEbus interface (i.e., no VMEchip2), the jumper may be installed or removed without affecting normal operation. J1 2 1 2 1 J1 System Controller (factory configuration) Not System Controller
相關產品
