欧美久久片软件夜_手机看免费毛片的网站_LSP破解软件库合集链接地址_国产成a人大片在线观看_醉酒后少妇被疯狂内射视频_精品人妻99一区二区三区_日本少妇综合高清_国产醉酒肤白貌美在线观看_最近2024年中文字幕高清_秋霞影院亚洲wm

DDC01.1-K200a
您可以將每個D/A轉換器（DAC）連接到10 V的內部參考電壓或連接到I/O連接器上外部參考（EXTREF）引腳的外部參考信號。施加到EXTREF的該信號應在±11 V范圍內。您可以配置每個通道以使用內部或外部參考。默認參考值選擇為內部參考。模擬輸出寄存器選擇在正常操作中，DAC輸出在使用新值更新時會出現小故障。故障能量因代碼而異，在頻譜中表現為失真。每個模擬輸出通道都包含一個reglitch電路，該電路在每個代碼處產生均勻的小故障能量，而不是在主要代碼轉換處產生大的小故障。這種均勻的小故障能量在頻譜中顯示為更新率的倍數。請注意，此reglitch電路并不能消除故障；這只會使它們的大小更加均勻。默認情況下，所有通道都禁用重新登錄，但您可以使用NI-DAQ為每個通道單獨啟用重新登錄。數字輸入/輸出設備包含八行通用數字輸入/輸出。您可以單獨使用軟件配置每一行的輸入或輸出。在系統啟動和復位時，數字輸入/輸出端口均為高阻抗。通用計數器0和1的硬件上/下控制分別連接到DIO6和DIO7上。因此，您可以使用DIO6和DIO7來控制通用計數器。上升/下降控制信號僅為輸入信號，不影響

You can connect each D/A converter (DAC) to the internal reference of 10 V or to the external reference signal connected to the external reference (EXTREF) pin on the I/O connector. This signal applied to EXTREF should be within ±11 V. You can configure each channel to use either internal or external reference. The default reference value selection is internal reference. Analog Output Reglitch Selection In normal operation, a DAC output will glitch whenever it is updated with a new value. The glitch energy differs from code to code and appears as distortion in the frequency spectrum. Each analog output channel contains a reglitch circuit that generates uniform glitch energy at every code rather than large glitches at the major code transitions. This uniform glitch energy appears as a multiple of the update rate in the frequency spectrum. Notice that this reglitch circuit does not eliminate the glitches; it only makes them more uniform in size. By default, reglitching is disabled for all channels, however you can use NI-DAQ to independently enable reglitching for each channel. Digital I/O The device contains eight lines of digital I/O for general-purpose use. You can individually software-configure each line for either input or output. At system startup and reset, the digital I/O ports are all high impedance. The hardware up/down control for general-purpose counters 0 and 1 are connected onboard to DIO6 and DIO7, respectively. Thus, you can use DIO6 and DIO7 to control the general-purpose counters. The up/down control signals are input only and do not affect the operation of the