欧美久久片软件夜_手机看免费毛片的网站_LSP破解软件库合集链接地址_国产成a人大片在线观看_醉酒后少妇被疯狂内射视频_精品人妻99一区二区三区_日本少妇综合高清_国产醉酒肤白貌美在线观看_最近2024年中文字幕高清_秋霞影院亚洲wm

DDC01.2-N200A-DS01-02-Fw
在安裝設備之前安裝軟件。有關軟件安裝順序的具體說明，請參閱以下相應的發行說明。1、安裝應用軟件如果您使用的是LabVIEW、LabWindows/CVI或其他國家儀器應用軟件包，請參閱相應的發行說明。2、安裝NI-DAQ驅動程序軟件請參閱您的NI-DAQ發行說明，并遵循其中針對您的操作系統和應用程序軟件包給出的說明?，F(xiàn)在可以安裝硬件了。硬件安裝您可以在計算機中任何可用的PCI/PXI擴展插槽中安裝PCI/PXI設備。但是，為了獲得佳的噪聲性能，請在設備與其他設備和硬件之間留出盡可能多的空間。以下是一般安裝說明，但有關具體說明和警告，請參閱您的計算機用戶手冊或技術參考手冊。♦ PXI-您可以在PXI或CompactPCI機箱中的任何可用PXI插槽中安裝PXI。注意：PXI-連接到CompactPCI J2連接器上的多條保留線路。在CompactPCI系統中安裝PXI之前，請參閱1章，將PXI與CompactPCI一起使用。CompactPCI系統使用J2連接器線路用于PXI以外的用途。2章安裝和配置PCI/PXI-用戶手冊2-2©National Instruments Corporation 1。關閉并拔下PXI或CompactPCI機箱。2、選擇未使用的PXI或CompactPCI外圍插槽。為了獲得佳性能，請將PXI安裝在支持總線仲裁或總線主卡的插槽中。PXI包含板載總線主DMA邏輯，只能在這樣的插槽中運行。如果選擇的插槽不支持總線主機，則必須使用軟件禁用板載DMA控制器。PXI兼容機箱必須對所有插槽進行總線仲裁。3、卸下所選外圍插槽的過濾器面板。4、觸摸底盤上的金屬部件，以釋放衣服或身體上的靜電。將PXI設備插入5 V插槽。使用噴射器/噴射器手柄將設備完全噴射到位。將PXI的前面板擰到PXI或CompactPCI機箱的前面板安裝導軌上。目視檢查安裝情況。8、插入并打開PXI或CompactPCI機箱。PXI現已安裝。

Install your software before you install the device. Refer to the appropriate release notes indicated below for specific instructions on the software installation sequence. 1. Install your application software—If you are using LabVIEW, LabWindows/CVI, or other National Instruments application software packages, refer to the appropriate release notes. 2. Install the NI-DAQ driver software—Refer to your NI-DAQ release notes and follow the instructions given there for your operating system and application software package. You can now install your hardware. Hardware Installation You can install the PCI/PXI- device in any available PCI/PXI expansion slot in your computer. However, to achieve best noise performance, leave as much room as possible between the device and other devices and hardware. The following are general installation instructions, but consult your computer user manual or technical reference manual for specific instructions and warnings. ♦ PXI- You can install the PXI- in any available PXI slot in your PXI or CompactPCI chassis. Note The PXI- has connections to several reserved lines on the CompactPCI J2 connector. Before installing the PXI- in a CompactPCI system that uses J2 connector lines for a purpose other than PXI, see Chapter 1, Using PXI with CompactPCI. Chapter 2 Installation and Configuration PCI/PXI- User Manual 2-2 © National Instruments Corporation 1. Turn off and unplug your PXI or CompactPCI chassis. 2. Choose an unused PXI or CompactPCI peripheral slot. For maximum performance, install the PXI- in a slot that supports bus arbitration or bus-master cards. The PXI- contains onboard bus-master DMA logic that can operate only in such a slot. If you choose a slot that does not support bus masters, you will have to disable the onboard DMA controller using your software. PXI-compliant chassis must have bus arbitration for all slots. 3. Remove the filter panel for the peripheral slot that you have chosen. 4. Touch a metal part on the chassis to discharge any static electricity that might be on your clothes or body. 5. Insert the PXI- device in the 5 V slot. Use the injector/ejector handle to fully inject the device into place. 6. Screw the front panel of the PXI- to the front panel mounting rails of the PXI or CompactPCI chassis. 7. Visually verify the installation. 8. Plug in and turn on the PXI or CompactPCI chassis. The PXI is now installed.