欧美久久片软件夜_手机看免费毛片的网站_LSP破解软件库合集链接地址_国产成a人大片在线观看_醉酒后少妇被疯狂内射视频_精品人妻99一区二区三区_日本少妇综合高清_国产醉酒肤白貌美在线观看_最近2024年中文字幕高清_秋霞影院亚洲wm

DS3820RDMB
-k2級
是并聯導體的校正系數，可通過
以下公式：
式中，n是每相并聯的導體數量；
-1.2是標準允許的磁閾值公差。
TN系統
小短路電流的計算公式為：
因此：
IT系統
當?shù)诙€故障將IT系統變成
TN系統。
有必要單獨檢查中性點未分布的裝置
中性分布。
ABB |電氣設備461
4保護人類
4.8保護人類的大保護長度
1SDC010044F0001
Dy L1
L2級
L3級
體育課
體育課
體育課
任
我
k L3 L2 L1 Z
體育課
我
k L3 L2 L1
中性點未分配
當發生第二個故障時，公式為：
因此：
中性分布
案例A：中性點分布式IT系統中的三相電路
公式為：
因此：
案例B：IT系統中的三相+中性電路，中性點分布
公式為：
因此：
462電氣設備| ABB
4保護人類
4.8保護人類的大保護長度
1SDC010045F0001
Dy L1
L2級
L3級
N
體育課
體育課
體育課
任
我
k L3 L2 L1 N Z
體育課
我
k L3 L2 L1
A、B
表格使用說明
已定義顯示大保護長度（MPL）的表格
考慮以下條件：
-每相一根電纜；
-額定電壓等于400 V（三相系統）；
-銅電纜；
-中性非分布式，僅適用于IT系統；
-保護導體橫截面符合表1：
表1：保護導體橫截面
相導體截面S保護導體截面SPE
[平方毫米
][平方毫米
]
s≤ 16秒
16<秒≤ 35 16
S>35秒/秒
注：相導體和保護導體具有相同的絕緣和導電材料
每當使用電子脫扣器的S功能（延遲短路）時
對于大保護長度的定義，有必要驗證
跳閘時間低于第4.5章表1中報告的時間值
對于TN系統和第4.6章表1中的IT系統。
對于與參考條件不同的條件，以下修正系數
應適用。

- k2
 is the correction factor for conductors in parallel, obtainable by the
following formula:
 where n is the number of conductor in parallel per phase;
- 1.2 is the magnetic threshold tolerance allowed by the Standard.
TN system
The formula for the evaluation of the minimum short circuit current is:
and consequently:
IT system
The formulas below are valid when a second fault turns the IT system into a
TN system.
It is necessary to separately examine installations with neutral not distributed
and neutral distributed.
ABB | Electrical devices 461
4 Protection of human beings
4.8 Maximum protected length for the protection of human beings
1SDC010044F0001
Dy L1
L2
L3
PE
PE
PE
REN
I
k L3 L2 L1 Z
PE
I
k L3 L2 L1
Neutral not distributed
When a second fault occurs, the formula becomes:
and consequently:
Neutral distributed
Case A: three-phase circuits in IT system with neutral distributed
The formula is:
and consequently:
Case B: three-phase + neutral circuits in IT system with neutral distributed
The formula is:
and consequently:
462 Electrical devices | ABB
4 Protection of human beings
4.8 Maximum protected length for the protection of human beings
1SDC010045F0001
Dy L1
L2
L3
N
PE
PE
PE
REN
I
k L3 L2 L1 N Z
PE
I
k L3 L2 L1
A B
Note for the use of the tables
The tables showing the maximum protected length (MPL) have been defined
considering the following conditions:
- one cable per phase;
- rated voltage equal to 400 V (three-phase system);
- copper cables;
- neutral not distributed, for IT system only;
- protective conductor cross section according to Table 1:
Table 1: Protective conductor cross section
Phase conductor cross section S Protective conductor cross section SPE
 [mm2
] [mm2
]
S ≤ 16 S
16 < S ≤ 35 16
S > 35 S/2
Note: phase and protective conductors having the same isolation and conductive materials
Whenever the S function (delayed short-circuit) of electronic releases is used
for the definition of the maximum protected length, it is necessary to verify that
the tripping time is lower than the time value reported in Chapter 4.5 Table 1
for TN systems and in Chapter 4.6 Table 1 for IT systems.
For conditions different from the reference ones, the following correction factors
shall be applied.